Installing a GPS tracking device in your vehicle shouldn't be a sophisticated activity, iTagPro technology nevertheless it is crucial to take security precautions, as such the installation should only be carried out by a professional Auto Electrician. Usually, it takes approximately 2 hours to set it up relying on the complexity of the vehicle’s wiring structure. GPS gadget set up (basic installation with no fuel/temperature/door sensors linked), read the next instructions. Read extra on the Do’s & Dont’s of GPS gadget set up at the tip of this doc. Screwdriver set, iTagPro official Plier, Multimeter and Wire Stripper/Cutter/Crimper. Before installing the device, you want to notice down International Mobile Equipment Identity (IMEI) number of the GPS tracking device and the SIM GSM quantity. Then insert the GPRS enabled SIM card to the machine. You may as properly download the vehicle addition template to report automobile information. Then insert the GPRS enabled SIM card to the gadget.

You might as nicely download the vehicle addition template to record car information. IMEI is a unique number to establish GSM, WCDMA, and ItagPro iDEN mobile phones, satellite phones, as well as some telematics gadgets that works as a singular identification code. This 15-digit number is often printed both on the underside of the GPS tracking unit or the machine case; you require IMEI to register the GPS tracking device on the fleet management software. Red wire (of GPS device) to at least one end and iTagPro official the facility supply of the automobile to the other finish of a 1Amp fuse. Secure the fuse to the instrument chord with a cable tie. Connect Black wire (-ve) on the harness to Chassis Ground (any bolt or iTagPro official wire with -ve power). Connect Yellow ignition sense wire to the vehicle’s ignition source to assist track ignition ON/OFF occasions. Please seek the advice of the car wiring diagram to find the ignition wire.

You'll be able to confirm the vehicle ignition wire by measuring the vehicle’s working voltage while the engine is working. Once identified, connect the ignition wire to the FUSE Box with a 3M Scotchlok so that it will snap into place and will get it correctly seated. Please check with the connection diagram below, for an in depth view of the wires & connectivities. One of the quickest and the most effective place to mount a GPS tracking device or iTagPro features a GPS tracker is below the dashboard or an exterior location in a horizontal position with a transparent view of the sky. Chances are you'll experiment with inserting the tracking device at totally different places on the car to find out the most effective reception for the specified degree of concealment. If the system has exterior GPS antenna then place the antenna beneath the dashboard or wherever convenient using double-sided sticky-tape to ensure it’s firmly fastened there. Once you’ve placed the GPS tracker within the vehicle, you’re all set.

Connect the wire socket and GPS/GSM antenna (of those with external antenna) to the GPS machine. As soon as the gadget is powered on, each green LEDs (GPS & communication) will flash on and off while looking for signals. When full sign energy is achieved, both LEDs will repeatedly illuminate. In order to validate performance, we have to ring the GSM cell number of the SIM. If it rings or responds with a busy notice, you'll be able to safely assume that the gadget is functioning properly. If there is no such thing as a response, you may should re-insert the SIM card and verify the wiring once more. Please Log into the platform with your credentials to ensure the device communicates with the server. Note: Make it possible for the IMEI no’s & mobile no’s you updated in opposition to the autos are right. To keep away from mishaps while set up, be sure the automobile ignition is turned off earlier than initiating wire connections. It's at all times advisable to disconnect the appropriate jumpers /connections of vehicle’s energy supply throughout the GPS system set up; this is to avoid brief circuits and wiring damages.

Ensure the wires keep disconnected whereas mounting/dismounting the gadget. Secure all wiring with Scotchlok, cable connectors, and electrical insulation tapes. Never enable any naked wiring to remain uncovered; connections should be least visible. Ensure additional insulation if wires go through a seen/exterior region, so as to keep away from quick circuit/wiring damages. GPS tracking devices may very well be mounted in a zone of restricted entry, so none has direct entry to the instrument. Keep connecting wires as discreetly as possible, making it much less visible and laborious to notice. For the security of personnel, system & car, iTagPro bluetooth tracker avoid connecting machine wires to the board computers (ECU) or management units. Ensure that you fasten wires to other wires/non-transferring elements and to not fasten near heat emitting and moving objects as friction/heat emission might trigger sparks resulting in brief circuits. While connecting ignition wire affirm if it’s the actual ignition wire (power provide available solely when the ignition is on). Using a multimeter, test power stream by turning on/off the engine.